Professionally made Magic Eye tube adapter, 6 pin to 8 pin socket. With this adapter the 1629 8-pin tuning eye tube and Russian 8-pin tuning eye tubes can be used, to replace any of the 6-pin tuning, magic eyes tubes (6U5, 6E5, 6G5, 6T5, 6N5, 6AB5, etc.). A switch was added on this adapter, giving you the option to use either 1629 tube or any of the Russian type tubes. This adapter has been tested with a 1629 tube and (6E5S, 6E5C, 6E5G, 6G5G Russian 8-pin tubes) and they work perfectly just like the original 6-pin magic eyes tubes. This adapter can also be made without the optional switch for either 1629 or Russian type tubes.
Magic Eye Tube Adapter (6 Pin to 8 Pin Socket)


Marantz Pioneer NAD Universal Pre OUT / Main IN Jumper
  Pair of custom made universal Pre OUT / Main IN Jumper plugs. These jumper plugs are used to interconnect MAIN IN and PRE OUT jacks. These professionally made jumper plugs, perform exactly the same as original jumpers, and will work on any receiver or integrated amplifier.


Marantz 6200/6300, Rotel RP-1500 Turntable Strobe Light Bulb, Strobe Lamp
  Professionally made, Marantz 6200, 6300, Rotel RP-1500 Strobe Light Replacement Bulb kit. I have restored many of the Marantz turntables over the years, with these strobe lights and they work perfectly. I made this strobe light, like original with the resistor and enough wire, giving you the option to install solderless or soldering the two wires as origina l (I highly recommend soldering wires). If you would like to install strobe light solderless, the wire connection will be included. Safety note: The strobe light circuit operates on 125 volts so please make sure the unit is unplugged before installation.
Professionally made, Blue LED fuse type lamp for Marantz, Sansui, Kenwood, Yamaha, Sony and other Receivers with 8 volts fuse type lamp. No need to worry about constantly replacing incandescent bulbs anymore. Led lamps will replace your dial and meter display lamps, giving your receiver a beautiful custom look. One led lamp draws about 20 milliamps, lasting ten times longer than incandescent bulbs. LED lamps are brighter, run much cooler and use less electricity. They are very easy to install, no modification or soldering needed. Carefully remove old bulbs, and install new led lamp into fuse clip, so the led faces the front of the display.

Thank you for visiting


I have belts for most brands. The following are some of the models I carry. If you do not see the model you are looking for, listed below, please contact me, before you buy. I carry many different models, I just can't list them all. Some of the different models I carry are, Admiral, Airmaster, Arvin, Belmont, Crowm, Coronado, RCA, GE, Detrola, Emerson, FADA, Fairbanks, Garod, Grunow, Howard, Kinght, Majestic, Philco, Silvertone, Sparton, Motorola, Airline(Montgomery ward), Bosch, etc.

Zenith models: 5F134, 5F233, 5F251, 5S29, 5S119, 5S127, 5S233, 5S251, 5X230, 5X248, 5X274, 6B107, 6J230, 6J257, 6J436, 6S128, 6S203, 6S222, 6S223, 6S229, 6S238, 6S239, 6S241, 6S249, 6S254, 6S256, 6S330, 6S341, 6S361, 6S362, 6V27, 7D126, 7D178, 7D203, 7D222, 7D223, 7D229, 7D239, 7D241, 7D243, 7D253, 7J323, 7J368, 7S53, 7S240, 7S363, 8S129, 8S463, 8S548, 8S661, 9S30, 9S54, 9S203, 9S204, 9S222, 9S232, 9S242, 9S244, 9S262, 9S263, 9S264, 9S307, 9S324, 9S344, 9S365, 9S367, 9S369, 10H551, 10S130, 10S155, 10S443, 10S669, 12H650, 12H689, 12H695, 12H696, 12S205, 12S232, 12S245, 12S265, 12S266, 12S267, 12S268, 12S345, 12S370, 12S371, 12S445, 12S453, 12S471, 12S475, 12S494, 12S550Z, 12S568E, 12S568Z, 12S569E, 12S569Z, 12S595Z, 12U158, 12U159, 15S308, 15S346, 15S372, 15S373, 15S479, 15S495, 15U246, 15U269, 15U270, 15U271, 15U272, 15U273, 601, 835, 880, 908, 935 950.
Chassis #:12A1, 12A2, 12A3, 12A4, 12B2, 1204, 1206, 1207, 14B1, 1501, 1502, 1502A, 1503, 22B1, 5522, 5523, 5638 , 5642, 5644, 5648, 5649, 5710, 5715, 5905, 5606, 5907.

LED Fuse Lamp Marantz, Sansui, Kenwood, Yamaha, Sony Receiver Light Bulb

Tube Radio Dial Belt


Pioneer Receiver Replacement LED Lamp Bulb
Professionally made, LED (clear or blue) T10 type bulb for Pioneer and other Receivers with 8 volts T10 type bulb. No need to worry about constantly replacing incandescent bulbs anymore. LED lamps will replace your dial display lamps, giving your receiver a beautiful look. One LED lamp draws about 20 milliamps, lasting ten times longer than incandescent bulbs. LED lamps are brighter, run much cooler and use less electricity. LED T10 lamps are made in two colors, ocean blue and clear color. They are very easy to install, no modification or soldering needed. Carefully remove old bulbs, and install new LED lamp into socket, so the middle LED faces the front of the display(see photos).

WaamampS